USD
EUR
GBP
EWS Remote Key 3 Button 315/433MHz ID44 Chip for BMW Fob
Placement for Part Numbers: FCCID: LX8 FZV
Work for fit BMW:
3 Series:
1997-1998 318i
1997 318is
1997-1999 318ti
2001-2005 320i
2000 323Ci
1998-2001 323i
1998-1999 323is
1999-2000 323ti
2001-2006 325Ci
2001-2006 325i
2001-2006 325xi
2000 328Ci
1996-2000 328i
1996-1999 328is
2001-2006 330Ci
2001-2007 330i
2001-2006 330xi
5 Series：
2001-2007 525i
2006-2007 525xi
1996-2000 528i
2001-2007 530i
2006-2007 530xi
1997-2003 540i
2004-2006 545i
2006-2007 550i
6 7 8 Series:
2004-2005 645 Ci
2006-2007 650i
1997-2001 740i
1997-2001 740iL
2002-2005 745Ci
2002-2005 745i
2006-2007 750i
1997-2001 750iL
2003-2007 760Li
2004-2006 760i
1997 840Ci
1997-1999 850Ci
1998-2006 M3
1999-2007 M5
2006-2007 M6
2004-2010 X3
2000-2010 X5
1996-2002 Z3
2003-2010 Z4
2000-2003 Z8
Programming Manual :
EWS System REMOTE KEY FOB PROGRAMMING INSTRUCTION FOR BMW "RUBBER" KEY
REMOTE CONTROL TRANSMITTER PROGRAMMING PROCEDURE FOR BMW - "RUBBER" KEY.
THESE INSTRUCTION ARE SUITABLE FOR BMW E46, E39, X3, X5 AND OTHERS PRODUCED TO 1999.
OEM PART NUMBER OF KEYS : 51218374929 / 66126955750 / 51218372844 / LX8FZV AND OTHERS.
NO TOOLS REQUIRED.
| 1. GET INTO THE CAR, CLOSE ALL DOORS AND INSERT THE KEY INTO THE IGNITION SWITCH. |
| 2. SWITCH THE IGNITION LOCK BRIEFLY TO IGNITION LOCK POSITION 1 AND SWITCH OFF AGAIN. THE SWITCHING TIME MUST REMAIN UNDER 5 SECONDS. |
| 3. REMOVE THE KEY FROM IGNITION SWITCH. |
| 4. PRESS BUTTON #1 AND HOLD IN. You must remove the key from ignition switch and press & hold button #1 within 5 seconds of removal. |
| 5. STILL PRESSING BUTTON #1 - PRESS BUTTON #2 THREE TIMES. |
| 6. RELASE BUTTON #1. LED 3 will flash slowly for a maximum of 10 seconds. When done properly the doors will automatically lock and then unlock. |
| 7. TEST REMOTE ( S ) TO ENSURE PROPER PROGRAMMING. |
If the LED does not flash or the central locking system fails to respond, you must repeat the initialization procedure.
If you possess additional transmitters for you vehicle (up to a maximum of 4 units) you must now initialize these as well.
Be sure that no more than 30 seconds is allowed to elapse between the individual initialization procedures.
Do not actuate the steering lock during this time.
How to set to 433MHz:
1. Hold on EWS1 Button, and then hold on EWS3 button with the other hand.
2. During you hold on EWS1, press EWS3 button 5 times in 5 seconds.
3. Frequency is 433MHz now, test frequency with programmer.
4. Start to program on car for working.
Cupronickel key blade
Provide wholesale
High quality
The keyblade needs to be cutted at your local dealer or a locksmith.
you need to go to your local locksmith store to program it too
You May Like
-
$18.90
-
$16.90
-
$33.90
-
$16.90
